Toelke Super D brace height?

old_goat2 · January 01, 2019, 11:05:30 PM

What brace height are you guys shooting your Super D at?

nineworlds9 · January 02, 2019, 12:22:02 AM

The two I had for a spell tuned 6 7/8 - 7"

Austin Brown · January 02, 2019, 06:21:33 AM

I like 6.75" on mine.

Sent from my SAMSUNG-SM-G891A using Tapatalk

Pat Ct · January 02, 2019, 12:53:14 PM

6 3/4 for me too

SquareHead · January 04, 2019, 09:43:26 AM

Another 6.75" brace height for me, also.

Jim Wright · January 04, 2019, 12:56:28 PM

I have 3 Super Ds, I draw 29" and shoot 12 to 1 arrows through mine. On the 64" bow I like 6 3/4", on the 66" 7" and on the 68" 7 1/4". That said, the world doesn't stop if I change the brace height a fair bit. The Super D is exceptionally well mannered and very "forgiving".

Pat Ct · January 04, 2019, 02:02:51 PM

Should have clarified: 6 3/4 on a 68" super D but it does just fine anywhere between 6 3/4 to 7 1/4 shooting carbon express heritage arrows cut to 31" with 250 gr up front. I'm pulling 55# at my draw.

tzolk · January 04, 2019, 04:02:54 PM

68" Super D's. 7 to 7-1/4

slowbowjoe · January 04, 2019, 06:04:07 PM

I think it'll vary with bow length. Check the website, it'll tell you, and Toelke's are a breeze to tune.

old_goat2 · January 04, 2019, 10:13:10 PM

Quote from: slowbowjoe on January 04, 2019, 06:04:07 PM
I think it'll vary with bow length. Check the website, it'll tell you, and Toelke's are a breeze to tune.

first place I went Super D isn't covered for that unless I overlooked it, and I looked more than once

old_goat2 · January 04, 2019, 10:14:46 PM

Looked again, not there on the mobile version of their page

tzolk · January 05, 2019, 07:19:42 AM

David,
Between 6 3/4 and 7 1/2. I wouldn't suspect you'd go out to 7 1/2 but as you know, Dan and Jared's bows are easy to tune. Throw some bare shafts through it. I usually use the same carbons for my equally weighted Whip. 64" Whip and 68" Super D. They bare shaft close enough. Both are 53@30. Brace on my D is 7 and 7 5/8 on the whip. I set the nock height on my Apache tillered D and whip to 5/8 for 3 under shooting. Ymmv of course.
Also, Dan's strings are so light, they should help squeeze as much energy as possible out of those limbs. Love those super D bows. They are proven killers in this house.
Did you get a new super D?

Eskanto · January 05, 2019, 01:11:08 PM

I shoot my 62" super D at around 7" but it shoots just as well at lower or higher brace heights so I don't have to worry much about it. I rarely need to adjust it even with different types of arrows... it is a very quiet and forgiving bow. When you get the strings from Dan along with the bow he also sends the recommended brace height range for that bow. For the 62", the range he sent me is 6 5/8 to 7 1/4. That may be different than longer versions. You can call Dan or write him an email and he will let you know for sure.

old_goat2 · January 05, 2019, 05:33:20 PM

Quote from: tzolk on January 05, 2019, 07:19:42 AM
David,
Between 6 3/4 and 7 1/2. I wouldn't suspect you'd go out to 7 1/2 but as you know, Dan and Jared's bows are easy to tune. Throw some bare shafts through it. I usually use the same carbons for my equally weighted Whip. 64" Whip and 68" Super D. They bare shaft close enough. Both are 53@30. Brace on my D is 7 and 7 5/8 on the whip. I set the nock height on my Apache tillered D and whip to 5/8 for 3 under shooting. Ymmv of course.
Also, Dan's strings are so light, they should help squeeze as much energy as possible out of those limbs. Love those super D bows. They are proven killers in this house.
Did you get a new super D?

New to me, I'm really not a D-Bow guy but I seen a deal on a 2 piece that I couldn't pass up. I've got just about every model bow that Dan makes except the Troll and if I ever see about used one of those in my wife's weight range I'll probably buy it. My draw length is too long for it or the Pika.