Main Menu

Taper ?

Started by SteveL, June 20, 2017, 04:49:00 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

SteveL

I'm almost embarrassed by these questions, but nothing ventured, nothing gained....

First I'm assuming that the measurement for the taper is how much per running inch.

But I'm wondering is the taper just one sided? So that the lamination if looked at closely would resemble a long ramp when viewed from the side - taper runs along the top and the bottom remains flat is what I'm imagining.

If the taper is like I think it is; then which side goes where - does the taper face the belly or back of the bow?

BTW, everyone on here is an artist to one degree or another. All the work I see is stunning. I almost drool over the bows I see being crafted here.

Thanks!

kennym

I grind both sides so it is probably taken off pretty equally from each side. I'm not sure you could tell anyway, and it would make no difference in how it goes in the bow.  :)
Stay sharp, Kenny.

   https://www.kennysarchery.com/

SteveL

I'm so glad I asked. I think I figured because of the way I saw the lamination sleds being used that only one side was being sanded on a slope.

So I guess this means when setting up a sled for the grind, that you set it to half the amount of total taper you need. Then flip it over side to side - not end for end and run it through again? Or heck maybe I'm over complicating this. I still haven't built my first bow yet, but I'm gettin' close   :)

Bvas

I've thought about this as well. But than realized that the slope is only in relation to the butt end of the lam. Once you grind the ends of the lams for a scarf joint, the whole concept is thrown right out the window.
Some hunt to survive; some survive to hunt

kennym

No, when grinding tapers, I have a 2" sled that I run thru the bandsaw against the fence with the workpiece at the blade, so I cut a taper on it to start with. Saves grinding and grain matches better than starting parallel and grinding the taper on it.

So less passes thru sander.
Stay sharp, Kenny.

   https://www.kennysarchery.com/

Mad Max

QuoteOriginally posted by SteveL:


So I guess this means when setting up a sled for the grind, that you set it to half the amount of total taper you need.  
Nope
.001 is .001
.002 is .002 ect.
when you flip it it's the same.
I would rather fail at something above my means, than to succeed at something  beneath my means  
}}}}===============>>

kennym

OOPS, missed that part!
Stay sharp, Kenny.

   https://www.kennysarchery.com/

Mad Max

That's because of your age.
  :goldtooth:
I would rather fail at something above my means, than to succeed at something  beneath my means  
}}}}===============>>

kennym

Stay sharp, Kenny.

   https://www.kennysarchery.com/

Crooked Stic

If you was building a ramp then you want all your taper on one side. But in the bow it aint gonna matter.
High on Archery.

Roy from Pa

I think yunzs are all cwazy...   :)

monterey

I think MadMax and
roy are the same person. :)
Monterey

"I didn't say all that stuff". - Confucius........and Yogi Berra

monterey

I just logged on using my wife's computer and didn't notice the dates!!!!!!!!!!!!
Monterey

"I didn't say all that stuff". - Confucius........and Yogi Berra

Roy from Pa

OH...

There are dates for these threads?

LMAO

:knothead:
:laughing:

monterey

Guess I was picking up loose ends.  Totally missed my opportunity last year to insult two members with one sentence. :)
Monterey

"I didn't say all that stuff". - Confucius........and Yogi Berra

bigbob2

Hilarious!.I grind from both sides as well helps tidy up any slight differences there might be from side to side.Also for ASL and deflex/reflex my rear lams are one piece and I grind to to the center from each side, so taper actually starts under riser. my riser templates etc, are shaped to suit.Mostly saves doing scarf joints.

Crooked Stic

Try this for S&Gs. Grind one side flat. then turn the lam over and grind your taper all the way out. Now close you eyes and flip the lam over several times real fast
. now lay it on the table ------------witch side is tapered----------- :dunno:

High on Archery.

Shredd

It's a Great Thread...  I learned a lot from it...  Thanks for rehashing it again...    :clapper:

Roy from Pa

Ya it's a great thread.

I'm just a little worried about Monterey..

:laughing:

monterey

Don't worry about me, I'm right here and comfortable sitting on my favorite asteroid looking down at you loons!  :biglaugh:
Monterey

"I didn't say all that stuff". - Confucius........and Yogi Berra

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2025 ~ Trad Gang.com ©