Pyramid Board Bow Questions

[razorback]

Ok, I posted in 4est's build along page that I had one in the works and since I found our camera I can give pics with the questions.
First: How is the tiller.

Unbraced.


Braced.


15 Inches.


20 Inches.


24 Inches.


Second: Due to the design of the bow, the straight grain I found runs out the side of the bow at one point. Is this going to be a problem. Seems like it is unavoidable with the sharp taper on this style of bow.

[John Scifres]

Looks good to me.  That's a good, sweet drawing, no stack tiller design.  It's really become my favorite profile.  Round in the middle, stiffer in the outer third.  6" of non-bending tips.  Since your tips don't bend a whole lot, make sure and reduce mass there by narrowing them as much as possible.

[stretch2]

i am no expert but it looks good to me

[razorback]

Dors the run out look like a problem to anyone.

[4est trekker]

The runouts are inevitable.  But, they are offset by the large working area on the back of the bow.  There's so much wood going into tension that the runouts won't become overstressed and fail. (At least in theory.  Sometimes they do fail, but yours look fine to me.)  It is critical that you round over the limbs' edges, however, or the sharp edge will give at the runouts.

Great looking bow, by the way!  Absolutely my favorite profile/tiller, as John said!  Thanks for posting!

[razorback]

I will get it finished up in the next day or two and post some final pics. Have to shoot a bunch of arrows through it to make sure the tiller stays the same. I think it will come in at around the 45# mark. I plan on using it at the Joan leonard  Memorial Bunny Hunt at the end Febuary, in New York.

[bamboo]

looks pretty good tony--round the edges good
the rabbits are already shaking!!!
-------------mike

[razorback]

Thanks Mike. If she don't blow up on me I will definetly bring it along. If nothing else it is wide enough to shield me from some of those legendary briars. I hope.

[George Tsoukalas]

Tiller looks great. grain looks good. What's your draw length? Jawge

[razorback]

Draw length on my recurve is 29-29 1/2. I have heard that longbows use a shorter draw. My string broke so have to twist up another one to finish it off. Should get that done tonight.

[soopernate]

Thats a new one on me...longbows using a shorter draw.  I think my draw is the same no matter what I am shooting whether it be a longbow or a recurve.

[George Tsoukalas]

I drew a recurve 29 in. I draw my selfbows 26 in. That could be old age.    Jawge

[soopernate]

Maybe I am just misinterpretting what I am reading(not unusual) I draw to the same anchor point no matter what bow I shoot and use the same form therefore I use the same draw no matter what I shoot...and similarly I use the same length arrows.

[razorback]

I'm just going on what I read. Havn't had much experience with selfbows or long bows. I will find out soon enough    The bow is 67" ntn 3' at its widest tapering to 1/2" nocks, to be thinned. The Handle/Riser area is about 10" making for about 28" of working limb. I think weight will come in about 45# with sanding and shooting in, which is very close to what I was looking for.

[razorback]

ot the string twisted up this afternoon, so can continue finishing up tonight. very happy to get the string right. They have been giving me fits to get right but re-read Sam Harpers instructions and realised I was doing too much twisting and that was causing all the poblems. got it now, thanks Sam.

[ron w]

Looks good to me,hope to meet you at the bunny hunt.....

[Sal]

Talk about protecting you from briars, 3' wide is a sheild!

I know you meant 3", which is still pretty wide.  Tiller looks good, grain as well.