Quote from: kennym on October 20, 2020, 04:14:02 PM
Dug 75'  of propane line .  This new deck thing shoulda been done when its not bow season...

Don't ya have lights on that backhoe?

No backhoe here.   

 

Back when I built mine, the lathe didn't solve it cause I had issue aligning the cylinder on the frame. What worked for me was to lay sand paper on the bottom board and rectify the cylinder in his final position on the frame

First limb off the form. Glue lines looking good.

How long is that bow going to be Z  ?

Quote from: Flem on October 20, 2020, 09:44:05 AM
That is a beautiful circular tiller No wasted limb wood on that one!

Thanks Flem, it took me a bit to work out how to tiller it, as this is the first bendy handle I've done. I went with just slightly stiff tips so I guess it's really very slightly elliptical.

Quote from: Pat B on October 20, 2020, 11:18:03 AM
Great tiller on a nice ash bow. Ash is one of those bow woods I don't have luck with. Everyone I've made fretted but I never heat treated an ash bow either. Well done on this ash bow.      

Thanks Pat, so far no fretting after a couple of hundred shots..... I was a little afraid it would and found a few little marks when tillering but discovered it was actually my scraper that was making the marks - with a file/rasp they disappeared and never came back 

Quote from: ztontonz on October 20, 2020, 12:41:22 PM
Nice work Flyonline!

Thanks, this is the first bow I'm happy with the tiller.

Quote from: Mad Max on October 20, 2020, 09:41:56 AM
Flyonline
How wide is it?

Thanks Mark, it's a tickle over 1.25" wide x .75" at the handle tapering straight to 5/8 x .5 at the tips. I plan on doing something like a pyramid next time, nice 'n' wide 

Quote from: ztontonz on October 20, 2020, 11:20:42 PM
First limb off the form. Glue lines looking good.

You chasing whales with hooks like that?   

" Thanks Flem, it took me a bit to work out how to tiller it, as this is the first bendy handle I've done. I went with just slightly stiff tips so I guess it's really very slightly elliptical."

Guess that depends on which part of the ellipse you are looking at

Quote from: ztontonz on October 20, 2020, 07:40:57 PM
Back when I built mine, the lathe didn't solve it cause I had issue aligning the cylinder on the frame. What worked for me was to lay sand paper on the bottom board and rectify the cylinder in his final position on the frame

Yeah, a true cylinder is only one part of the alignment. I am going to have to shim the bottom board a touch to get it perfect with the drum surface, but that isn't too major of a problem.

Those are wicked hooks on your new limbs, I look forward to seeing how it all looks and bends when complete.


Mark

Quote from: Mad Max on October 21, 2020, 12:20:27 AM
How long is that bow going to be Z  ?

Well, my initial plan was to do a 60". But I noticed last night that I screwed up the wedges length/position. So my current plan is to build it as a 64", run some test and then drill holes to make 60".
It's part of prototyping. No mistake. All part of the learning curve

WoW, Z....   Looks extreme...  What is the radius near the tip??

Hey Max how many inch past the hook did you cut your nocks? 2"?
I was thinking of making 2 sets of grooves for test purposes

Quote from: ztontonz on October 21, 2020, 01:41:28 PM
Hey Max how many inch past the hook did you cut your nocks? 2"?
I was thinking of making 2 sets of grooves for test purposes

1-1/2", I think longer could be better

I want to see the string angle at full draw, looks like your limb is short, it might make it open up NICE

Quote from: Shredd on October 21, 2020, 01:17:31 PM
WoW, Z....   Looks extreme...  What is the radius near the tip??

That would be close 1.75" sir

Thanks Max

Glued up another limb. Shaped pads and back of the handle.

How long is the riser?

16,5"