2019 Bow Swap Thread

goobersan · February 23, 2019, 11:04:39 PM

lookin AWESOME Dannon

Roy from Pa · February 24, 2019, 02:39:04 AM

Very nice, Dannon.

I really enjoy seeing the risers you glass guys put together.

Almost makes me wanna make a glass bow.

skeaterbait · February 24, 2019, 05:48:19 AM

Quote from: Roy from Pa on February 24, 2019, 02:39:04 AM
Very nice, Dannon.

I really enjoy seeing the risers you glass guys put together.

Almost makes me wanna make a glass bow.

You are closer than you realize Roy, you actually put an "L" in glass this time instead of a "W"

Roy from Pa · February 24, 2019, 05:53:05 AM

I can fix that:)

LOL

Buemaker · February 24, 2019, 05:59:40 AM

Riser looks great.

Crooked Stic · February 24, 2019, 07:29:34 AM

Dannon save your cut off pieces from the pads and use them to clamp your limb pad pieces on. Gives a flat surface and things dont slip around as bad.

kennym · February 24, 2019, 07:42:59 AM

Looking good !! I need to get to work on mine.

Dannon · February 24, 2019, 09:26:59 AM

Quote from: Crooked Stic on February 24, 2019, 07:29:34 AM
Dannon save your cut off pieces from the pads and use them to clamp your limb pad pieces on. Gives a flat surface and things dont slip around as bad.

That's what I was doing but the still tend to slide around a little bit. Thanks for the kind words guys!
Dannon

Flem · February 24, 2019, 09:39:15 AM

Thats some wild looking wood Dannon. Looks like you drew it with a Etch A Sketch.

Crooked Stic · February 24, 2019, 01:18:15 PM

Had to put new tape on one end so a sneak peek at Sycamore and tulip poplar[attachment=1][attachment=1]
[attachment=2]

goobersan · February 24, 2019, 01:55:57 PM

W

W
Looks sharp Mike

Roy from Pa · February 24, 2019, 02:10:44 PM

Not too shabby ole timer..

Flem · February 24, 2019, 02:31:57 PM

Sycamore. You guy's are providing an education for me in the use of wood that I would never have considered for Bow's. Show's what I know.

Never want to stop learning!

kennym · February 24, 2019, 02:34:58 PM

Lookin good Mike!

Closing in , needs final sanding and some finish

Sent from my iPhone using Tapatalk

Crooked Stic · February 24, 2019, 03:06:38 PM

I like that Kenny. Ibeam phenolic or G 10
O I can only imagine the power of the PINK wedge.
[attachment=1]

Roy from Pa · February 24, 2019, 04:16:05 PM

O I can only imagine the power of the PINK wedge.

Mike, ah never mind.

LOL

Buemaker · February 24, 2019, 04:38:18 PM

Very nice Kenny. I knew it, when you get going you really get going.

kennym · February 24, 2019, 05:46:28 PM

Thanks Bue!

Mike it is phenolic, had it here and would have had to order G10...

4 point · February 24, 2019, 06:15:17 PM

Kenny and Stic, good look'n bows! I wasn't sure the pink wedges were actually going into the bow but there they are.

Bvas · February 24, 2019, 06:26:57 PM

A lot of good lookin work goin on

Finally got a start on my victims bow. Riser pieces cut. Now for some some quality time sanding to fit.

Unless.........my victim loves big thick glue joints???

[attachment=1]

[attachment=2]