3Rivers Archery




The Trad Gang Digital Market














Contribute to Trad Gang and Access the Classifieds!

Become a Trad Gang Sponsor!

Traditional Archery for Bowhunters




RIGHT HAND BOWS CLASSIFIEDS

LEFT HAND BOWS CLASSIFIEDS

TRAD GANG CLASSIFIEDS ACCESS


Main Menu

Footed Carbon Shaft

Started by KyRidgeRunner, January 29, 2019, 10:10:18 PM

Previous topic - Next topic

0 Members and 2 Guests are viewing this topic.

KyRidgeRunner

Question for the guys who shoot footed carbon shafts.  This is my first time playing with them (I get crazy Ideas and tinker when season goes out).  Anyhow my question is; when I foot the shaft does the arrow have to be long enough for the footing to be in front of the shelf or can the aluminum footing come back onto the shelf?  If it matters I'm using a 2117 to foot a standard goldtip Hunter shaft. 

M60gunner

To be honest I never thought about that. Maybe cause I have a piece of toothpick under my shelf material (Velcro). That probably raises the shaft enough the foot doesn't catch on anything. I also chamfer the back end of the foot.

Jason W

It really does not matter if the footing comes back onto the shelf. I have all my arrows footed. Been doing it for years. Makes that carbon "bomb proof".

There is so many ways to do it. Tinker and see what you like.

Heck, I have even took the Carbon express Bulldog nock collars and used them. They actually work pretty good as footings. I would not recommend them solely, but they work pretty good on your everyday arrows.

I personally like my footing 1.5"-2" long.

I also agree, if you make them yourself, taper the ends of your footings. Makes a cleaner pull on the target and if the footing does come in contact with the shelf material, it saves on it.

We sell many sizes on our site if your interested.

Basically, I cant recomend them enough! They really strengthen the carbon.

Jason W


Porkchop1

I've only shot wood shafts for the last 15 or more years so I'm not familiar with footing a carbon shaft.  Thanks for the picture it helps, but how is the footing held in place?  Is the aluminum shaft picked there there is little to no gap between the two?
Porkchop

Tomas Stieber

IMHO a footing over an inch is overkill and may start to alter the spine of the arrow, slightly.

Jason W

The footing is basically glued on.
Everyone has their favorite adhesives.
Clean the shaft and footing really well with alcohol or acetone. Then glue her up!

Yes, it is aluminum.

Tighter fit, the better!

The one smaller gray one is Top hat stainless steel. It has a lip on it. I like to glue that onto the end of the shafts first, then glue insert in. Makes a great square end and they are durable. I have been experimenting with these TopHAt ones. I like them.

I am thinking about carrying them on my site along with my Arra Foots!

Anyway, I am glad to help out in any way. PM,Email or call anytime!

Jason W

Quote from: Tomas Stieber on January 30, 2019, 12:25:40 PM
IMHO a footing over an inch is overkill and may start to alter the spine of the arrow, slightly.

Yes it will!
You should always do your tuning and testing with the footing installed!
The little footings I mentioned and showed do not effect spine at all.
1" and over....yes!

ozy clint

Quote from: Tomas Stieber on January 30, 2019, 12:25:40 PM
IMHO a footing over an inch is overkill and may start to alter the spine of the arrow, slightly.

it only starts to alter spine once is extends back beyond where the insert finishes, which can be seen as another tuning option. this might allow the use a lighter spine arrow and longer footing for higher FOC. as for overkill, once the rear of the footing is behind the insert, the closer the back of the footing is to the arrows balance point (center of gravity) the less chance of the arrow breaking behind the footing because the center of gravity has a much shorter lever on which to impart lateral forces on the shaft on angular hits.
Thick fog slowly lifts
Jagged peaks and hairy beast
Food for soul and body.

Border black douglas recurve 70# and 58# HEX6 BB2 limbs

KyRidgeRunner

Good info here guys.  Thanks for the help! 

PistolPete

I foot my arrows with a "cap" footing, which is the aluminum arrow with insert in it, which slips completely over the end of the carbon shaft. I think this makes it even stronger, since it completely contains the end of of the carbon while transferring the force of an impact into the rear of the aluminum insert, rather than into the shaft wrapped around the insert.



I also adjust the length of the footing to tune the arrow, rather than the length of the arrow shaft itself. I draw 32" so I need the arrow to stay full length. And a longer footing allows me to use a lighter spine arrow, which weighs less, which gets me more FOC.

Trenton G.

For those who make their own footings, what do you use to cut aluminum shafts? I keep imagining the shaft collapsing.

PistolPete

I'm sure most use an arrow saw, but I use a grinder with cutting wheel. Then I clean/square things up with case trimming and chamfer tools from my reloading stuff.

ozy clint

i use a little tube cutter like the plumbers use on copper pipe. it cuts it square then i debur with tools from my reloading kit like pete says.
Thick fog slowly lifts
Jagged peaks and hairy beast
Food for soul and body.

Border black douglas recurve 70# and 58# HEX6 BB2 limbs

Jason W

Quote from: ozy clint on February 04, 2019, 03:04:32 PM
i use a little tube cutter like the plumbers use on copper pipe. it cuts it square then i debur with tools from my reloading kit like pete says.

This ^^^
I also sand/bevel the edges. Just like the ones we sell

hybridbow hunter

The tophat system ( steel collar and steel insert) is really wonderfull and they have so many different diameter listed than everyone can find the best one for his shaft.
I use it on black eagle outlaw 350 with 92 gr steel insert. Fitting is perfect with tight tolerance and arrow end is really strong with that combo

[attachment=1,msg2849211][attachment=2,msg2849211]

La critique est aisée mais l'art est difficile.

Jason W

 :tongue:
Quote from: hybridbow hunter on February 07, 2019, 02:38:11 PM
The tophat system ( steel collar and steel insert) is really wonderfull and they have so many different diameter listed than everyone can find the best one for his shaft.
I use it on black eagle outlaw 350 with 92 gr steel insert. Fitting is perfect with tight tolerance and arrow end is really strong with that combo

[attachment=1,msg2849211][attachment=2,msg2849211]

Looks very similar to what I have been doing. I love the TOP HAT products.

Bldtrailer

If you foot the same length as your insert you will find the shaft breaks there when hit hard . a little longer and it seems to greatly improve arrow strength,  I foot 3555(500) and 1535(600)  gt trads  with 1-2 inches of 2117 and (700) 2013 . I use 1 -1 1/2 inch inserts and adjust the footing to be longer than the insert. Then I tune.[attachment=1]
As we get older our bow weight goes down and our body weight goes up, One of Lifes little jokes.
Bringing Archery to
Wounded Warriors

Bldtrailer

[attachment=1] I also foot the nock ends 1/4 3/8 same as the front
As we get older our bow weight goes down and our body weight goes up, One of Lifes little jokes.
Bringing Archery to
Wounded Warriors

KyRidgeRunner

Thanks to everyone who replied and posted pics.  I got my new bow today so I'll be tuning up some arrows this week. 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2025 ~ Trad Gang.com ©