FHLB build Mostly done now!!

[Roy from Pa]

 

[Mad Max]

Nice build along

[Roy from Pa]

This better son?

[attachment=1,msg2938277]

[attachment=2,msg2938277]

[attachment=3,msg2938277]

[Shredd]

  purty curves on her...

[Mad Max]

Where did you get that Yeller masking Tape

[kennym]

Thanks Roy , you prob just put some chriorpratcors outta biz tho!


Mark, bought that on ebay, said it was 1.5" wide, well it ain't It is a metric narrower than 1.5"

I bought 12 rolls of it and just use it here and there cause I didn't wanna send it back.

Told the seller and they said it was sold to them as 1.5 and they never checked it...

[Autumnarcher]

I bought a roll of the blue tape was supposed to be 1.5" opened up and it was 2 rolls of 3/4". I think its a conspiracy to screw us up. they also did some of that metric mumbo-jumbo so I dont even know what it really works out to.

[Roy from Pa]

That's why I don't make dem gwass bows...

Ya gotta worry bout a 1/16th of an inch here and there....

[Shredd]

I bought a roll of the blue tape was supposed to be 1.5" opened up and it was 2 rolls of 3/4". I think its a conspiracy to screw us up. they also did some of that metric mumbo-jumbo so I dont even know what it really works out to.

now that really cracks me up... watcha expect one roll of 1 1/2"??      lucky you didn't get 3 rolls of 1/2"...    just too funny... i'll be laughing all night every time I think of this one...

[Roy from Pa]

 

[kennym]

Raining this morn so a bit of work on this, planning to be in stand bout 2

Temp is dropping 25 degrees today by dark , should be a good afternoon

I leave the line and the edge sander makes it straight

[attachment=1,msg2938369]

[attachment=2,msg2938369]

[Roy from Pa]

Cool...

[mmattockx]

I leave the line and the edge sander makes it straight

Is that cut with a bandsaw?

Good luck with the hunt, I've found the animals are restless and moving a lot as a big storm or cold front rolls in, then they bunker down until after the storm passes.


Mark

[kennym]

No I grind them on a 6" disc with 40 grit, 10 minutes to the lines and way cheaper than bandsaw blades...

Thanks, I'm about to head out, but wind is 18 mph now! LOL

[Buemaker]

Seems to be a lot of conspiracies these days now one in 3/4 inch.  I use the 2 inch yellow tape, put it on the glass and just cut off the overhang with a sharp knife.

[Nicholi]

[attachment=4,msg2938227]

Kenny, I know I'm off topic a bit here, but can you tell me a little bit about your drum sander? How big is it? Have you ever sanded down the edge on a whole bow on a smaller one? Do you have problems keeping it even, or is it pretty good?

[Flem]

I don't think thats a drum sander, it looks like a really sweet wide belt
Now I have some serious tool envy

[Roy from Pa]

That emergency stop has me wondering:)

[Mad Max]

I think it's a G0527

https://www.grizzly.com/products/grizzly-18-5-hp-wide-belt-sander/g0527

[kennym]

Yep, 527  18x48 belt  it's a hog of a sander.  You could run them on a drum sander just the same.  If the first side I do on the disc is straight, so is the one that gets done with the big sander.  They are usually really close tho.