Will maple boards that I have seen at lowes make a good bow? Im not sure what kind of maple they are. I did see some with decent grain.
If the grain is good yes they will. I recently made one from an HD maple board but backed it with a slat of hickory. This board probably could have been a self bow but it's going to someone else and I wanted insurance.
Here's some pics.
(http://i95.photobucket.com/albums/l144/NDanforth83/101_1523-1.jpg)
(http://i95.photobucket.com/albums/l144/NDanforth83/101_1511.jpg)
(http://i95.photobucket.com/albums/l144/NDanforth83/101_1505.jpg)
(http://i95.photobucket.com/albums/l144/NDanforth83/101_1510.jpg)
Diddo. Here's one a made for my wife out of maple backed with brown paper:
(http://i984.photobucket.com/albums/ae321/isaacscr/Maple%20Static%20Recurve/HPIM3637.jpg)
(http://i984.photobucket.com/albums/ae321/isaacscr/Maple%20Static%20Recurve/HPIM3640.jpg)
(http://i984.photobucket.com/albums/ae321/isaacscr/Maple%20Static%20Recurve/HPIM3651.jpg)
(http://i984.photobucket.com/albums/ae321/isaacscr/Maple%20Static%20Recurve/HPIM3667.jpg)
(http://i984.photobucket.com/albums/ae321/isaacscr/Maple%20Static%20Recurve/HPIM3665.jpg)
Do you think the maple is more reliable than the red oak? Does it splinter as easy?
Sorry for all the questions, but i just had a red oak board bow crack on the lower limb.
maple is slightly denser that red oak, but both make a good bow. maple tends to be a little more forgiving. go for it. we don't have maple at lowes or HD in texas.
Those are beutiful bows! Our stores dont have maple either,I smell a roadtrip in my future!! :D
I am going to try the maple, If the grain is good do I need to back it? Does the maple have the tensile strength for no backing?
I had good results with maple trim boards, {2"x1" which is 1 3/4" x 3/4"}
I made some 66" piramid, and straight limbs tapering the last 15" , a Holmegard, 70" all in the 50# range at 28",and a few kid bows 48" with these boards.The kid bows ranged from 36# at 24" to 20#@24".
I tried using Maple Veneer as a backing on some, but the "veneer" failed.The bow underneath was fine, so I removed the backing and cleaned up the glue mess.
For the kid bows I rip the board on the band saw , and glue on a handle,and cut out a shelf. They are all piramid style and have turned out great.It only takes about an hour and half to make a kid bow like this.I get 2 kid bows per board this way too.
Trim boards sell for about $1.50 a linear foot, making these very cheap to make and practice tillering on.
Pete
Pete,where do they sell maple trim boards? Are they from a specialty shop, or can we get them at the big box stores?
4est, tell me about the glue on nocks, on the belly side of the bow.- it looks interresting
wayne
Let me recommend you find a local cabinet maker for a good source of maple.Maple is commonly used by them and they get just as good a wood as retailers at a fraction of the cost
maple will make a fine unbacked bow. same rules apply for picking out board. grain running straight from one end to the other as close as you can get. on the edge and at least one other side.
I get maple trim from Windsor Plywood lumber yards, but every lumber yard here caries Maple trim. You do need to sort thru for good pieces.
Pete
4est
ya sure like those floppy rests- so they obviously work well- any particular reson you prefer them over a glued on shelf on those shoot off the knuckle bows.
regards
wayne