I've checked the archives in the "how to" section, and tried searching the site too, but to no avail. Maybe i've been spoiled by 4est's build a long, but I haven't found anything that can teach me some sort procedure as to how to make my own arrows.
Can someone lead me in the right direction? I have turkey feathers that I need to learn how to prep, and would also like to see what end I taper to what degree and yadda yadda. All the good stuff. I'm hoping to start making arrows asap but not without the proper tutolage first.
C'mon 4est do an arrow buildalong!!
try looking on the build along section down near the how tos. also i think jawge has some on his site.
QuoteOriginally posted by walkabout:
try looking on the build along section down near the how tos. also i think jawge has some on his site.
I looked at the how to's, but could only find stuff for footing or cresting arrows or splicing feathers. I was just looking for a simple start to finish how to for the fundamentals of arrow building.
yea the buildalong i saw was from starting from a shaft to the fletching, didnt show how to make the shafting, etc.
Maybe I'll put one together for folks. I use mostly homemade tools and jigs to make my arrows. I have to confess, though, that I start with poplar dowels from Menard's, and not raw materials when making my shafts. I have done it that way, but I don't have the patience or the time anymore.
I use a homemade:
spine tester
taper jig
feather grinding jig
feather shaping jig
cresting maching
I use a commercial:
fletching jig
point/nock taper tool
I'll see what I can put together for you.
I have a video on it, but there isn't much detail at all. I completely cut out the spine tester. I do plan to do a written build along for my web page that will have lots of detail. I don't cut or burn my own feathers, though. Anyway, here's the video:
http://www.youtube.com/watch?v=4Nve9CetSKg
I'm glad someone got 4est to look at doing another how-to. And 4est, if you could go ahead and include how to make a homemade:
spine tester, taper jig, feather grinding jig, feather shaping jig, and cresting machine
:)
Maybe someday you could just auction yourself off for a long weekend for St. Jude's? :notworthy:
Will be following this one....
Jeremy
Jon, I make all my arrows from either cane or hardwood shoots. I only use a spine tester to find the stiff side of the arrow which goes against the bow. Google "James Hill Spine Tester" for complete instructions on how to make one using a dial indicator. Very easy! I don't crest arrows anymore but made my cresting machine using an old rock tumbler when I was using cedars.
For the tapering for points and nocks I made a jig to use with my bench top belt/disc sander. The tapers are 11 degrees for the nock and a 5 degree taper for the point.
For fletching I cut and grind them from turkey and goose feathers. I use a Young Feather Burner to shape the fletching after they are on the shaft. I split the feathers, cut them to size and use a fletching clamp to hold the feather while I grind the quill on a belt sander. Sometimes I use a JoJan fletching jig but mostly I tie them on as per the Cherokee/Woodland style of 2 fletch or 3 fletch.
I have made shafting from white pine and poplar by cutting the board into 3/8" square stock first than hand plane them by removing the four corners with a thumb plane($8 at ACE Hardware). Then remove the 8 corners with the plane and sand them smooth after that.
See Making a Simple Arrow on my site. Jawge
http://georgeandjoni.home.comcast.net/~georgeandjoni/
I make what I call "high performance" wood arrows. Very closely matched in weight and spine, the last 9" of the shaft tapered to 5/16", precision cut point and nock tapers, heat straightened shafts and fletched with high profile feathers. It takes me a while to make a dozen but they are incredible shooters.
Next time I make up a batch I will take some pictures of the process.
Here you go its the one I followed
http://***********.bowsite.com/TF/lw/thread2.cfm?forum=23&threadid=190256&category=
QuoteOriginally posted by 4est trekker:
Maybe I'll put one together for folks. I use mostly homemade tools and jigs to make my arrows. I have to confess, though, that I start with poplar dowels from Menard's, and not raw materials when making my shafts. I have done it that way, but I don't have the patience or the time anymore.
I use a homemade:
spine tester
taper jig
feather grinding jig
feather shaping jig
cresting maching
I use a commercial:
fletching jig
point/nock taper tool
I'll see what I can put together for you.
And i'll bet you'll create another bad a$$ buildalong! I say this cause I think I saw some of your arrow tools, and arrows, on the site already.
That's a great link waldo! Sulphur makes it look easy.
I have done them like Sam's video. I find that making a match dozen set of arrows is twice the work of making a bow even if you use a drill and dowel cutter instead of a hand planing. That is if you stain, cap and crest too.
Well for right now I'd really like to just learn the fundamentals or the art, like checking spinage, fletching, nocking and tipping. The fancy pants stuff can come after I can make some arrows on my own.
4est i wouldn't mind knowing how you made your spine tester, feather shaper, and feather ginder either. I hope you'll either PM me or post on here how you made them.
I agree. It would definitnely be nice to know how to make some of my own tools that will prep feathers. I'd be willing to buy a cutter tho, for $25 from 3rivers that would be the way to go.
I did dig up this post 4est put up on my homemade tools thread a while ago. It shows his fether chopper, grinder, and some of the arrows that caused me to want to make my own:
http://tradgang.com/noncgi/ultimatebb.php?ubb=get_topic;f=125;t=002727;p=2#000021
I have made this spine tester and it seems to be pretty good. I believe ishiwannabe also made this same one and has posted pictures of it. If you study it carefully and follow the directions you can do it very easily. PM me with any questions.
Also added link to the other style of tester that many have made with great success.
http://www.bambooarrow.com/tester.html
http://www.jamesmhill.com/Spine_Tester.html
If you have a router and want to save some $$ over the Veritas dowelling jig to turn shafts from wood, I have tried the following home-made jig:
http://books.google.com/books?id=CYy5hoY-tZwC&pg=PA203&lpg=PA203&dq=the+precision+dowel+maker&source=web&ots=GJYCljrJj_&sig=QuL06SuouzzhX0kPlpK8h-StDvY#PPA202,M1
(same idea but differnt implementation of the jig http://lumberjocks.com/topics/193 )
Yes, you will have a lot of saw dust from this and needs a lot of sanding. But that's fun to make your own jig and shafts. To make a matching dozen of shafts you may need to turn 4 dozens of wood.
The dimensions I used are slightly different comparing with what's given in the link:
(Shaft size)______(Entry)_____(Square)
5/16"______________3/4"________1/2"
11/32"_____________3/4"________1/2"
23/64"_____________3/4"________1/2"
a different set to use is:
5/16"______________5/8"________0.442"
11/32"_____________5/8"________0.442"
23/64"_____________5/8"________0.442"
Drill bit price at Lowes
5/16" Hitachi, $4.07, L=4.5"
11/32" Hitachi, $4.77, L=4.75"
23/64" Hitachi, $5.17, L=4.875"
3/4" fostner, Porter Cable, $9.97, L=3.75"
5/8" fostner, Porter Cable, $8.97, L=3.75"
I Stacked 3 piece of 3/4" maple board to make the jig.
I recently bought a book called The Traditional Bowhunter's handbook and the chapter on arrows gave me a lot of vital information that I had not considered before. Arrowmaking is fun, but if not done right can result in a split shaft going through your hand in you are not careful.
Blessings, Bruce
I believe that 3Rivers has a video(DVD) with all the basics of wood arropw making.
i have a buildalong on here also
GREAT post!
the lumberjocks link alone was golden
i've made about 200 arrows now, i'm just figuring out what spine is. all this time i just thought i was a horrible archer! now i see that i'm a horrible archer who makes horrible arrows!
QuoteOriginally posted by Innocente:
GREAT post!
the lumberjocks link alone was golden
i've made about 200 arrows now, i'm just figuring out what spine is. all this time i just thought i was a horrible archer! now i see that i'm a horrible archer who makes horrible arrows!
that made me laugh my ass off!! i'm still laughing