I know this has been discussed in length, but I just can't seem to figure this out. I'd like some help if y'all don't mind.
I'm running out of arrows and carbon shafts are too expensive. I've looked around and seen that I can usually get 2 dozen or more POC shafts for the same price as 1 dozen carbons. I know they're a bit more work but I'm alright with that.
What I'm shooting is a Bear Polar recurve. It pulls about 59# at 29" which is my draw length. I've seen that there are a lot more options for 125gn heads than the heavy weights I've been using so I was thinking of switching to those. What should I be looking for? I really don't know what to even start at.
My bow looks to be cut to center with about a 1/8" pad for the arrow rest. I'm using the Bear carpet kit for that. I have a B50 string with otter fur string silencers.
I've been using GT Traditional 340 arrows full length with 225gn heads and 5" shield cut feathers. They've been pretty good but I don't have the tools and things to cut and adjust them. Wood would be much easier for me and I'd be able to shoot without so much worry. I've broken 3 arrows this year, carbons are just getting too expensive for me to be shooting at ground targets and the like.
When you buy commercial wood shafting the stated spine range is set for a 28" finished arrow with a 125gr. head. For each inch over 28" you can subtract 5# of spine weight or add 5# for each inch shorter. A Grizzly 2 blade or Wensel Woodsman 3 blade are 2 very good 125gr. heads. Both easy to resharpen and their width/length ratio is good for penetration.
I haven't bought shafting in a long time...for my selfbows I used to go with about 10# under draw weight for spine and for my old style Treadway longbow I shot 60-65 spined arrows for my 56#@26"(cut to 28") draw. I would guess 55-60# or 60-65# spined cedar shafts for a 29" draw with a 125gr head.
At 29" your arrows with 125gr heads will shoot 5# under stated spine.
Pat: Think you got the direction of your subtraction and addition mixed up. The addition or subtraction assumes a commensurate increase or decrease in draw weight and arrow length. I.e., 50#@28 is 53# at 29, etc. Too, the longer arrow will have a dynamically softer spine. Thus, he would need to increase static spine as draw length increases to compensate for the increased draw weight and reduced dynamic spine of the longer shaft.
Regardless, Dorado, a .340 spine is equivalent to about 93#. Even if you have a fair amount of weight on the front end, and the shafts are full length, they're going to be on the stiff side for your bow.
If you go with a point in the 125 grain range, a 11/32 POC shaft spined about 65-70# should work, give or take a little. Would be a good idea to get a test kit starting at 60-65, through 65-70 and 70-75.
Another reason you don't need as much spine with the wood shaft is that it is larger diameter than the carbon shaft, which is probably 5/16 in diameter or smaller. The effect of the larger diameter shaft is the same as building out the side plate. It holds the center of the arrow further from the center of the bow, thus it needs to flex more to clear the bow cleanly when shot. That means the spine has to be reduced a bit so the shaft will flex more easily around the riser.
It also makes a difference on how hard a particular bow shoots and whether one has a soft release or a hard release. If money is part of the equation, this gives you the chance to use Zwickey Eskimos or Hunter's Heads from 3 Rivers. Probably 65-70s, I recently bought a dozen Rose City premiums, for over $40, three are going be pheasant arrows. Wapitis are over $40 as well, but they will cut arrows to length and taper them for a few bucks, they send out very good shafts.
Here is a general guide to begin with.
http://pin.it/Vas436O
Call the guys at Surewood and ask them for help. If it was me I would start with 60-65 spine, 65-70 spine and see which flys best. With your longer draw and woods spined at 28" I would say at least 5# over your draw weight maybe 10#.
I recommend these guys because the shafts I have gotten did not need a lot of straightening if any at all. These are Doug Fir and not Cedar shafts. Plenty good to start with.
Do you know the year of your Polar? It had a longbow look in the 50s and a recurve design later in life. That would make a big difference.
My Polar is a 1958, it's just before the Bear coin in 1959. It's like a hybrid between a longbow and recurve. It's not as curved as a recurve, but much more than any r/d longbow I've seen. I say it's not a recurve because the string doesn't touch the limb once it leaves the grooves. Flings arrows with authority too. I got a lot of hand shock with light arrows and it was a bit noisy. I switched to heavier arrows and heads and it became quiet and smooth. Hence the 340 spined carbons and 225gn heads.
So, 60-65 or 65-70 to start and maybe 10# higher than bow weight. I'll see if I can get me a test kit and some field points next payday.
Longbow Fanatic 1, Thanks for that chart. According to it I should be good around 65-70. I'll look for a test kit that's on both sides of that.
Now about material. I've read that Port Oxford Cedar and Douglas Fir are the two best materials. Is that correct? Which would y'all suggest?
Doug Fir is heavier. Surewood Steve can be a big help, too, on spine suggestion. Give him a call.
Steve 541-688-0493
I recommend getting a test shaft batch from surewood so you can always dial in before you buy for any bow, then buy tapered raw shafts from them and finish them. I just write the spine on the shaft with a pen, wipe on 2-3 coats of helmsman gloss spar urathane from a can with a rag, then fletch with duco cement. As bomb proof as arrows get. If you use/get your own turkey feathers you can save half the cost.
Doug Fir it'll be then.
Soon as I can I'll give Surewood a call and see about ordering a test kit. I'll save their number.
I need to go turkey hunting this year. I'd really like to get me some feathers. Until then I'll have to sink a lot into buying some. Then again I don't have a feather chopper so I'm sunk there too.
Speaking of feathers. Does it matter on how I orient the grain with wood arrows?
Before fletching align your nock so the tightest grain of the shaft is against the bow side plate as that is the orientation the supplier will use when grading spine for hand matched shafts.
Darado, I have a simular bow, year etc. Does the bows profile when strunglook a bit different to you? Mine does, almost a recurve bend in the top limb but more of a R/D bend in lower limb. I put this to a bowyers forum and was told this could be a "breasted" tiller. My question was bow safe to shoot? The answer was yes, now I am trying to find out if this a common thing or do I have a time bomb here.
Thanks, TomM
My limbs are definitely different. Shoots fine though and no signs of cracking. If I'm not mistaken these are aluminum cored. The aluminum came from B-29 superfortresses. Mine's still in one piece so I can't verify that. I've flung hundreds of arrows out of mine and it's been doing just fine.
Tightest grain against the side plate. So opposite of cock feather. That'll be easy.
Sagittarius Archery for fletching. 100 shield or parabolic 5" for $30. $26 for 4". Die cut, not chopped. Shipping is reasonable.
Can't really go wrong with Douglas Fir. They make great arrows.
Sagittarius Archery. I've not heard of them. Great prices though. I'll save that. Thanks.
If your going to change to save money, its going to be a lot cheaper in the long run to go with carbon. Good wood shafts are going to run you at least $40 per dozen. They will not hold up nearly as well as carbon. On a dozen carbon, 12 out of 12 will shoot the same. Not so with wood. I love wood arrows, but the consistency and durability of carbon are far better than wood.
QuoteOriginally posted by Brian Bishop:
If your going to change to save money, its going to be a lot cheaper in the long run to go with carbon. Good wood shafts are going to run you at least $40 per dozen. They will not hold up nearly as well as carbon. On a dozen carbon, 12 out of 12 will shoot the same. Not so with wood. I love wood arrows, but the consistency and durability of carbon are far better than wood.
That's why I started with carbon. Problem is, I don't have any way to cut them, and dropping $90-$100 for a dozen arrows that may break on the first shot is a bit much for me right now. That and my back yard has a hunger for arrows. I swear that it'll reach up and eat any arrow that touches it. Since I like ground targets that gets expensive.
Judo points and dollar store foam footballs ;)
"I'm running out of arrows and carbons are too expensive"....we need to chat...
"Break on the 1st shot"...what horribly made carbons are you shooting????
Carbons are NOT that expensive....You MUST take into consideration of the fact that they are more durable and will last longer. I'm not here to argue about it cause this if fact to me as I am a living example...I have judo arrows I"ve had for year...no telling how many shots some have had.
I might break one or two a YEAR stumping.....
So, for me carbons are CHEAP.
Not trying to talk you out of wood...just making sure you know more about carbons and money. That old 'to expensive' claim went out a decade ago ...especially when some carbons became radial wrapped, thicker walled, and yes, even heavier. AND MUCH MORE DURABLE.
The old claim 'carbons are too light' went out about the same time. My carbons weigh about 85 grain more than my aluminums I used early 80s with the same broadhead.
Now...good wood arrows are still available....a lot of the old growth woods are gone to its a bit more difficult....BUT!...we have some Sponsors here that DO have quality stuff. Check out the Sponsors list if you still want to go with wood...any of them can help you out.
When considering long term wear and tear things tend to balance out. There are certainly aspects of any shaft that fit certain situations better or worse. Arrow loss when small game or bird hunting is a big one with me. I do not feel as guilty when I leave a basic wood arrow behind as when I leave an aluminum or carbon or fiberglass arrow behind. On one farm I hunted, the farmer got an arrow in his combine tire and was not happy. Thankfully, it was not one my woodies that I had used for rabbits and pheasants in the same area, because he demanded to inspect the arrows of the hunters that were using his land. It was a plastic fletched carbon.
I've been using GT Traditional blems. I broke one first shot into a bag target. Probably just a QC slip. Not something I'm worried about. I've lost two this year. One my yard ate, the other I broke on a rock I didn't see.
I'm on an extremely limited budget due to massive medical bills and loss of work. I'm not giving up on carbons, but I can get 2-3 times as many woods for the same price. I also picked up some 125gr glue-on field points at a yard sale a while back. That's one of the main reasons I'm looking at wood. I'd like them for practice so that I can save my carbons for hunting once I get proficient enough for that. I'd sooner loose a basic wood arrow than a carbon.
Carbons will save you money in the long run. Shooting wood will only be a short term solution.
As near as I can tell if your true string leaving the fingers length is 29", you would probably need 70-75 spine shafts with 125 grain heads. I do not have any of that size in my stash.